Please help me.
I want to save these 16 data individually.
If I press Cerrent, an error appears, such as a pop-up [An error has occurred].
1. [Save inputs to independent measurements] is checked in [input Selection].
2. Both Java and REW are up to date.
Is there any way?
Hi AVNirvana!
So I'm looking to do some upgrades to my home studio in terms of acoustic treatment. At the moment I only have some 1 and 2 inch cheap foam at first on first reflections on the walls and ceiling, and a bookshelf in the back right corner. I realize they don't do all that much and...
Asio driver used used to work just fine in my windows 10 htpc. Recently i downloaded the dirac trial and tried to check the results .
When i try to choose the asio4all driver the app instantly shuts down . It happens with and without the dirac live plug in running . I deleted and re installed...
Hi everyone,
May I get some advice here?
I have tried to flatten the SPL response of my room over the whole spectrum.
My strategy has been: using MSO to handle the lower part of the spectrum and then using REW EQ filters for the rest.
For the low end, I optimize with MSO until 300 Hz and I...
Hello all,
I searched but it seems that there is no way in REW to import biquads. Is there?
If not, is there a way (or a hack) to paste or append biquads into a REW's .req file?
Many thanks.
Hello,
I have performed an optimization of my listening position with REW and a convolution plugin. To calculate the EQ filters, I used some averaging of the MPL and other surrounding positions.
The result is quite decent for the MPL and positions close by.
Then I had the (terrible) idea to try...
I would like to compare delay of signal passing through subwoofer to delay in stereo speakers. Purpose is to align the signals in the crossover point using phase adjustment on subwoofer.
Can I use REW with only a Umik-1 from minidsp for this?
I'm completely new to REW and it seems like the...
Deer Creek Audio has published a new blog post covering Home Theater Multi-Subwoofer Setup for miniDSP, REW and Dirac Live. This paper walks you through the setup of your home theater multi-subwoofer configuration using the miniDSP 2x4 HD, DDRC-24 or Flex. This process helps optimize the...
I searched the forum to see if this issue had already been addressed, but didn't find anything. I apologise if I'm going over well-trodden ground.
My brand-new HP dy5088 laptop will not work with REW because of a mismatch between the audio format the laptop supports and the audio format REW...
At Deer Creek Audio, we have published a new white paper covering Stereo 2.1 & 2.2 Subwoofer Optimization for miniDSP, REW and Dirac Live.
This white paper describes integrating and tuning a subwoofer into your 2.1 or 2.2 system using the miniDSP 2x4 HD, DDRC-24, SHD, SHD Studio, SHD Power or...
Dear REW community,
I was wondering if downsampling affects the measurements with REW. I noticed that the default setting in the sound card settings is 48 kHz. My external sound card does not automatically switch to this value and operates at 44.1 kHz by default. Does this "mismatch" have any...
Hi, I’m a newbie to REW. I have some confusion about sub measurement as follows:
- When I perform the measurement of L+R should I keep my sub on or off?
- if I should keep it on, what should I set the sub volume and crossover to?
- If I should turn off the sub and measure it separately (with...
Hi Folks. Newbie here. I have performed my first measurement with UMIK-1 and REW. I need your help to understand how to generate & translate my EQ measurements into RME parameters.
I could not find a way to generate EQ according to RME parameters and capabilities. I tried using Generic EQ with...
Hi, I have a laptop with Linux Mint where I am running the previous major release of REW. I usually use UMIK and it works perfectly - as well as the internal soundcard both for FR and impedance measurement. I tried to set up two channel measurement using the UMC1820 sound card and ECM8000 mic...
Hello all,
I've looked through the available information here but have not found anything resembling my issue, so here it is.
My AVR is connected to computer via HDMI and it sees 7.1 and I can hear test tones from each speaker when using windows sound settings.
In Rew it will not play individual...
Hi John~
Today i trying to use a soundcard to measurement impedance,but looks like hi pass not working on measurement(but works on levels),so i can"t do imp cal. It will be great if hi pass works again;)
In 2019, I purchased Audiolense XO to try. Long story short, I couldn't get it to work due to an odd error I kept getting. Fast forward to 7 months ago when I interviewed Mitch on my podcast here. The more we talked, the more I wanted to try Audiolense. After the podcast Mitch asked me if I...
Is REW supposed to be pronounced 'REW' (like my name without the 'd') or 'R-E-W' (letter-by-letter)? I know that the program's full name is Room EQ Wizard.
Hi,do you have any plan to add full iso3382 measurement ?Something very useful like STI。
:rubeyes:
And,if rew have “limit curves”(can be modified) will be very helpful to tell if loudspeaker system fit hifi standard like IEC60581。
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.